How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
This great article below on the subject of A Step-by-Step Guide to Installing a Bathtub is quite stimulating. You should check this stuff out.
Installing a tub isn't specifically rocket science, however it does require solid plumbing, woodworking, and also in some cases, tiling skills. Changing an old bathtub with a new one is likewise a reasonably difficult project. If the old tub is easily obtainable, the task can move quickly; if you have to open up a wall surface to get rid of the old tub and position the brand-new tub, the job is a lot harder. In either case, the project is within a house handyman's skills, although you will certainly require a helper to leave the old bathtub and also embeded in the new one. Make sure you have qualified yourself for the task and are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is far better to consider employing one before you start. Opportunities are you might need a professional plumber to make tube connections.
This short article will assist you set up a brand-new bath tub in your bathroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water supply pipes.
Your tools as well as material checklist must make up the following:
Planning for the Installment
To start with, the sustaining structure provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is essential to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Utilize the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bath. Make sure you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last position.
Removing Old Taps
If you need to change old taps with new ones as a part of your installment, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be fairly troublesome due to the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, use the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
Prior to moving on to fit the new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bathtub
Using both wood boards under its feet, position the bathtub in the required position. The wooden boards are valuable in uniformly spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next goal is to ensure that the bathtub is leveled all round. This can be achieved by checking the spirit level as well as changing the feet on the tub up until the spirit level checks out level.
To set up taps, fit the bottom of the furthest flexible tap connector to the suitable supply pipe by making a compression join; then do the same for the other faucet.
Activate the water and also examine all joints and also new pipework for leaks and tighten them if necessary. Fill the bathtub and likewise inspect the overflow outlet as well as the typical outlet for leakages.
Finally, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bath tub needs to wait till the bath tub has actually been made use of a minimum of once as this will settle it into its final placement.
Suitable New Touches
If the tails of the brand-new faucets are plastic, then you will require a plastic adapter to stop damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for lowering couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin ensuring that the washing machines remain in location between the faucet and also the sink. Protect the tap in place with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with regular faucet connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break a rigid seal, creating the water to penetrate the wall surface between the bath as well as the tiling, resulting in difficulties with moisture and feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and installations. They are sold in tubes as well as cartridges, and can securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to always load the tub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break rather early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily readily available on the market. It is suggested to fit the tiles making use of water-resistant or water resistant glue as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been made aware of that editorial about How to Install a Bathtub from a good friend on another web address. Do you know anybody else who is excited by the subject? Feel free to share it. I value reading our article about A Step-by-Step Guide to Installing a Bathtub.
View Report this page